طرق الدفع منتجات الشركة حجز الكورسات Dealer Area

الحصول على  VIP

 

 

صيانة الهاردديسك والداتا ريكفرى

 نسيت كلمة المرور
 التسجيل
 

بحث
مشاهدة: 637|رد: 0

[شرح] SEGATE SELF TEST AND DETAIL

[نسخ الرابط للاقتباس]

62

المواضيع

267

المشاركات

1426

الأرصدة

عضو ذهبي

Rank: 6Rank: 6

الأرصدة
1426
  • تم شكره 25 مرة
  • قام بالشكر 0 مرة
تم نشره منذ 2016-02-01 14:09:25 | رؤية جميع المشاركات |نمط القراءة فقط

01-03 pretreatment (may clear all FW)
hard disk installation and servo calibration tests, including 01-02
01 - Manufacturing temporary log
02 - Formatting and test error logs, two heads and circuit calibration test
03 - servo correction information
04-0F servo test (including scanning defective plates)
04 - oblique wave loading / unloading test
05 - Sensor Lag Test
06 - head switching test
07 - RUNOUT compensation Test
08 - When checking the servo error writing on the disk 2T type
09 - head low-flying display
0A - Head stability test
0C - read servo defect test position
0D - re-check RRO ZAP test
0E - Looking Skip cylinder test (not yet realized)
0F - currently written test
10-1F channel to optimize test
heads and circuit calibration test
10 - 1E, 2A - 2E adaptation region # (last area) 0 through - all of the heads
1F - show suitability, VCO, and DIODE temperature setting
20-2F servo parameter debug
2F - Display settings FIR adaptive
servo performance verification tests
20, TEST 60 - Servo Visits
21, TEST 25 - RRO / NRRO Test
23 - Start / Stop (10)
24 - Start / Stop (2,000 times)
29 - servo defect scanning
30-3E defect scanning, analysis, processing (precise scan for bad sectors and for shielding)
Find and redistribution defect test
30 - Verify that all disk groups to read, AT Level
31 - wedge-shaped defects scan head 0-1 without reading level, 50 W class
32 - wedge-shaped defect scanning. 2-3 head without reading stage, grade 50 W
36 - 0-1 wedge on the scan head to find out the defects located
37 - 2-3 wedge on the scan head to find out the positioning defects
with 3A-1 Repeatable read all of the heads polished and defect testing, repeated 50 times
3B-establish defect table; filling damaged head 0,1
3C-establish defect table; filling damaged head 2,3
3D-establish defect table; filling damaged head 4, 5
3E-establish defect table; filling damaged head 6,7
3F-loopback test, written by testing
40-4E logically work test (without any repair, just as the factory can * test, as long as any one procedure finds an error that the hard drive is not appropriate for the factory)
error rate performance test
40 - Start / Stop (10)
41 - Track intrusive
42 - SPIN STAND simulator - minor bug green area
43 - RAM Test
46 - Data compilation Ratio
47 - Cold write / erase tracks show
48 - Low level format, write-through
49 - write / read / compare (zero style)
4A-compensation coefficient detection
4B-read of all sectors
4B - show all tracks Cold write
head flying height measurement 4C-
4D- Automatic data collection FA
accumulation 4E-checking health and create self-summary
or 50 4F
4F-Failed Disk Test
50 - through the disk test
special test
51 - Error Rate
52 - RRO test disk group to write
54 - Pick crooked measuring
55 - one million random read and write
56 - write / read / compare (zero style)
61,62,63 - Manufacturing Reliability Test
64 - Head stability testing
65,66,67 - Media Delay Test


يجب عليك تسجيل الدخول قبل إضافة رد تسجيل الدخول | التسجيل

قوانين النقاط

New Page 3


友情插件推广,完美枫枫wanmeiff友情插件推广,完美枫枫97yun友情插件推广,完美枫枫jzxyh

إتصل بنا|الأرشيف|الهاتف المحمول|الغرفة المظلمة|sitemap|عالم إحتراف الهاردوير  

بتوقيت جرينتش +8, 2019-10-19 07:35 , Processed in 0.164869 second(s), 29 queries .

Powered by Discuz! X3.1 Licensed

© 2001-2013 Comsenz Inc.

Arabic By DiscuzAr

الرد السريع عودة إلى الأعلى عودة لقائمة الأقسام